Product Specs
General Specifications
- Maximum Rating
- 340 BHP
- Displacement
- 538 in³
- Minimum Rating
- 325 BHP
- Governor and Protection
- Electronic (ADEM™ A4)
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1 or 2
- Flywheel Teeth
- 113 (SAE 1), 134 (SAE 2)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5.8 in
- Bore
- 4.4 in
Emissions
- Emissions
- EPA and CARB Non-Road Tier 3,EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
Dimensions
- Length
- 43 in
- Width
- 32.6 in
- Height
- 40.3 in
- Weight
- 1576 lb
Capacity for Liquids
- Lube Oil System - Refill
- 8 gal (US)
- Cooling System
- 3.7 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Turbocharger, separate circuit (SCAC) or remote (REMAC)aftercooler
- Single, right-side, center-mounted turbo with water-cooledturbine housing
- Air inlet 101.6 mm (4 in) connection type
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Fuel cooled ECU
- Power compensation for fuel temperature
- Programmable low and high idle
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speed, temperature,pressure)
- J1939 broadcast (diagnostic and engine status)
- Certified electrical control system (hazardous environment only)
- Derated engine: automatic ambient temperature compensation
-
- Cooling System
-
- Thermostats and housing, RH forward-facing outlet — 51 mm(2.01 in) connection
- Jacket water pump — belt-driven, centrifugal
- Water pump — inlet RH facing downward 63 mm (2.48 in)
-
- Exhaust System
-
- Exhaust manifold — water-cooled
- Single, right-side, center-mounted turbo with water-cooledturbine housing
- Rear facing turbo exhaust 81.8 mm (3.22 in) connection, nonV-band clamp
-
- Flywheels And Flywheel Housing
-
- Mandatory selection of:SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation
-
- Fuel System
-
- HEUI fuel system
- Fuel filter — secondary, LH (2-micron high performance)
- Fuel transfer pump — left front
- Fuel priming pump — left front
-
- Lube System
-
- Crankcase breather — LH
- Crankcase fumes disposal — with integrated service indicator, LH
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump
- Oil filler — top mounted
- Oil level gauge — LH side
- Oil pump — gear-driven
- Oil valve sampling
- Preservation of turbocharger, flywheel, and crankcase
-
- Power Take-offs
-
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter,22.3 mm (7/8 in) wide
-
- General
-
- Vibration damper
- Lifting eyes
- Automatic variable timing — electronic
- Literature
-
- Mandatory Options
-
- Flywheel housing and flywheel
- Throttle position sensor and/or throttle control
- (Non-hazardous environment only)
- Primary filter/water separator
- Turbo orientation
Attachments
-
- Air Compressors
-
- Air compressors
- Air compressor governor
-
- Air Inlet System
-
- Air cleaner
- Precleaner
- Air inlet elbow
- Air shutoffs
-
- Charging Systems
-
- Charging alternators
- Alternator mounting
- Alternator belt tensioner
- Alternator pulleys
- Alternator guards
-
- Cooling System
-
- Radiators
- Fan drive and pulley — f/u/w radiator packages
- Fans f/u/w radiator packages
- Coolant level sensor
- Fan drive mountings
- Fan adapters
- Fan adapter for blower fans
- Fan pulleys
- Fan height instructions
- Vee belts for customer-supplied radiators
- Suction fans and blower fans
- Water inlet elbows
- Dry charge coolant conditioners
-
- Emissions Certifications
-
- IMO certification
-
- Exhaust System
-
- Flexible fitting
- Turbocharger exhaust outlet adapters
- Elbows, flange, pipes, clamp
- Rain caps
- Manifolds
- Mufflers
-
- Flywheels And Flywheel Housing
-
- Crankshaft seal
-
- Fuel System
-
- Flexible fuel lines
- Water separator and fuel filters
- Fuel cooler
-
- Instrumentation
-
- Gauges and instrument panels
- Interconnect harness
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pans
- Drain and cover
- Oil level gauges
- Remote oil filter
- Oil fillers
- Lubricating oil
- Fumes disposal
-
- Mounting System
-
- Structural steel base
- Engine support — front and rear
-
- Power Take-offs
-
- Enclosed clutch
- Clutch supports
- Flywheel stub shaft
- Hydraulic pump drives
- Hydraulic gear pumps
-
- Starting System
-
- Starting aids
- Electric starting motors — 12V and 24V
- Battery sets — 12V and 24V (dry)
- Battery cable
-
- General
-
- Tool set