Product Specs
General Specifications
- Maximum Rating
- 275 BHP
- Displacement
- 442 in³
- Minimum Rating
- 205 BHP
- Governor and Protection
- Electronic ADEM™ A4
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1,2, or 3
- Flywheel Teeth
- 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5 in
- Bore
- 4.3 in
Emissions
- Emissions
- EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
Dimensions
- Length
- 41.5 in
- Width
- 29.8 in
- Height
- 40.6 in
- Weight
- 1386 lb
Capacity for Liquids
- Lube Oil System - Refill
- 36 gal (US)
- Cooling System
- 78.2 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Fuel cooled ECU
- Power compensation for fuel temperature
- Programmable low and high idle
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speed, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Certified electrical control system
- Derated engine: automatic ambient temperature compensation
-
- Cooling System
-
- Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
- Jacket water pump — belt-driven, centrifugal
- Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
-
- Exhaust System
-
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Exhaust manifold — water-cooled
- Front turbo exhaust
-
- Flywheels And Flywheel Housing
-
- Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
-
- Fuel System
-
- HEUI fuel system
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — left front
- Fuel priming pump — left front
-
- Lube System
-
- Crankcase breather — top rear
- Crankcase fumes disposal — RH
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump, 31 L (33 qt) oil change capacity
- Oil filler — front top valve cover
- Oil level gauge — LH rear
- Engine oil pump — gear-driven
- Oil valve sampling, RH
-
- Power Take-offs
-
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
-
- General
-
- Vibration damper
- Lifting eyes
- Literature
- No paint
-
- Mandatory Options
-
- Flywheel housing and flywheel
- Primary filter/water separator
- Turbo orientation
Attachments
-
- Air Compressors
-
- Air compressor governor
-
- Air Inlet System
-
- Precleaner
- Air inlet elbow
- Charging System
- Cooling System
-
- Emissions Certifications
-
- IMO certification
-
- Flywheels And Flywheel Housing
-
- Crankshaft seal
-
- Instrumentation
-
- Gauges and instrument panels
-
- Lube System
-
- Oil pans
- Drain and cover
- Remote oil filters
- Lubricating oils
-
- Mounting System
-
- Structural steel base
- Engine support — front and rear
-
- Power Take-offs
-
- Rear enclosed clutches
- Hydraulic pump drives
- Crankshaft pulleys
-
- General
-
- Tool set