Exterior View
Product Specs
Engine Specifications
- Minimum Rating
- 2619 kV·A
- Maximum Rating
- 3325 kV·A
- Emissions
- Available in IMO Tier II/ EPA Marine Tier 2 configurations
- Engine Control
- Dual ADEM™ A4
- Generator Set Control
- MPD 3.0 / Cat® Alarm and Protection System
- Weight
- 53599 lb
- Speed
- 1200/1500/1800 rpm
- Aspiration
- Turbocharged/2-stage aftercooled
- Bore
- 6.9 in
- Displacement
- 5164 in³
- Fuel System
- Common Rail/EUI™
- Oil Change Interval
- 1000 h
- Stroke
- 8.7 in
Dimensions
- Height
- 50 Hz - 2928 (115 in) / 60 Hz - 2916 mm ( 115 in)
- Length
- 50 Hz - 6782 mm (267 in) / 60 Hz - 6742 mm (265 in)
- Width
- 50 Hz - 2413 mm (95 in) / 60 Hz - 2125 mm (84 in)
Capacity for Liquids
- Cooling System - Engine
- 92 gal (US)
- Lube Oil System - Refill
- 250 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Dual turbochargers
- Corrosion-resistant aftercooler core
- Air cleaners — single or dual element
-
- Exhaust System
-
- Dry exhaust manifolds with thermo-laminated heat shields
- Dual turbochargers with water-cooled bearings and thermo-laminated heat shields
- Vertical exhaust outlet
- Flange and exhaust expanders
-
- Cooling System
-
- Separate-circuit-aftercooler (SCAC) and jacket water (JW) circuit cooling system
- Gear-driven centrifugal pumps, one for each circuit
- SCAC electronic thermostat, outlet-controlled with aftercooler inlet temperature sensing
- JW electronic thermostat, outlet-controlled with outlet temperature sensing
- Engine oil cooler in JW circuit
-
- Fuel System
-
- Cat common rail high-pressure fuel system with electronically controlled unit injectors
- Duplex primary fuel filter with water separator
- Duplex secondary/tertiary fuel filters
- Electric fuel priming pump
- Gear-driven low pressure transfer pump
- Gear-driven high pressure transfer pump
- Double-walled high pressure fuel lines
- Fuel pressure, temperature, and leak detection sensors
-
- Lubrication System
-
- Engine-driven, gear-type oil pump
- Integral lube oil cooler
- Front-mounted oil drain lines and valve
- Oil sampling valve
- Filler and dipstick
- Four-canister simplex oil filter
- Prelube pump — electric, air, or custom
- Fumes disposal with crankcase breathers
- Crankcase explosion relief valves
-
- Engine Control And Protection
-
- Dual ADEM A4 engine control unit (ECU) for redundancy
- Software monitors engine parameters and performs alarm, derate, and shutdown functions
- Rigid wiring harness
- Marine Power Display 3.0 (MPD 3.0)
-
- Mounting
-
- Inner-outer base with vibration isolators
-
- Generator
-
- Kato brushless permanent magnet 6P6.6-3200 HR
- 2-bearing, close-coupled arrangement
- 60 Hz, 600V, 0.7 PF
- UL/CSA listed, IP23
-
- Flywheel And Coupling
-
- Flywheel housing, SAE No. 00
- Flywheel, SAE No. 00
- ABS certified, non-certified, or custom-coupling and coupling mounting
- Free-standing or close-coupled generator set arrangements
-
- Starting System
-
- Turbine air starter or
- Dual electric starting motors or
- Air and electric starting motors (redundant)
-
- General
-
- Power distribution box — 24V or custom
- 20A battery charger
- Cat yellow paint
- Offshore oil field sub-base
- Integral spring isolators with limit stop
- Lift provisions on base
- Oil drain extension
- Engine length drip pan with drain
- Torsional dampened driveline couplings
Attachments
-
- Air Inlet System
-
- Air cleaner service indicator
-
- Cooling System
-
- 9 kW, 240V, 60 hz jacket water heater
- Custom jacket water heater
-
- Fuel System
-
- Four canister duplex oil filter
-
- Engine Control And Protection
-
- Cat Alarm and Protection System
- Communication module PL1000T/E
- Direct-rack control
- Thermocouples
- Metal particle detector
- SOLAS spray shielding
-
- Mounting
-
- Custom I-beam base with vibration isolators
-
- Generator
-
- Custom generator
-
- General
-
- TVA report
- Special tests
- Project-specific installation drawings
- P&ID-electrical drawings
- Spare parts kit
- Barring group
- Engine lifting group
- Custom generators and radiators