Product Specs
Engine Specifications
- Minimum Rating
- 440 BHP
- Maximum Rating
- 595 BHP
- Emissions
- EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Rated Speed
- 2100 r/min
- Bore
- 5.4 in
- Stroke
- 6.75 in
- Displacement
- 928 in³
- Aspiration
- Turbocharged-Aftercooled
- Governor and Protection
- ADEM A3
- Engine Weight - Net Dry
- 2743 lb
- Oil Change Interval
- 250
- Rotation from Flywheel End
- Counterclockwise
- Flywheel and Flywheel Housing
- SAE No. 0 or SAE No. 1
- Flywheel Teeth
- 136 (SAE 0), 113 (SAE 1)
Capacity for Liquids
- Minimum Cooling System - Engine Only
- 5.5 gal (US)
Dimensions
- Length
- 54 in
- Width
- 37 in
- Height
- 48 in
Standard Equipment
-
- Air Inlet System
-
- Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature, pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
-
- Cooling System
-
- Thermostats and housing — outlet vertical
- Jacket water pump — gear-driven, centrifugal, RH
- RH front water pump inlet
- All plugs/fittings are STOR for lines gp water
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
- Full marmon connection, maximum load 10 kg for direct connection to turbo
-
- Flywheels And Flywheel Housings
-
- See Mandatory Options
-
- Fuel System
-
- MEUI system
- Fuel filter, secondary, mid-mount (LH 2 micron high performance)
- Fuel transfer pump, LH front
- Fuel priming pump, LH mid-mount
- Fuel sample valve, mounted on fuel filter base
-
- Lube System
-
- Crankcase breather — rear valve cover
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — on oil filter base
-
- Mounting System
-
- Front support (shipping only)
-
- Power Take-offs
-
- Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
- Hydraulic pump drive, SAE A, 11 tooth
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins, sockets)
- Literature group owner and operator
-
- Mandatory Options
-
- Throttle position sensor
- Exhaust system — front or rear
- Flywheel housing or rear PTO
- Primary filter/water separator
Attachments
-
- Transmission Arrangement
-
- Transmission cooler
- Tool set
-
- Air Compressor
-
- Air chambers
- Air compressor governor
-
- Air Inlet System
-
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
-
- Charging System
-
- Charging alternators
- Alternator mountings
- Alternator wiring
- Circuit breaker mountings
- Alternator belt guard
-
- Cooling System
-
- Radiator — installed
- Radiator — ship loose
- Fan drive f/u/w Caterpillar installed radiator
- Fan drives for customer-supplied radiators
- Fan height instructions
- Vee belts for customer-supplied radiators
- Aftercooler lines f/u/w Caterpillar installed radiator
- Rear-facing exhaust
- Aftercooler lines
- Suction fan adapters — attaches fan to fan pulley
- Blower fan adapter — attaches fan to fan pulley
- Blower fan
- Suction fan
- Fan belt tightener
- Coolant level sensor
- Dry charge coolant conditioners
- Dry charge coolant conditioner element
-
- Exhaust System
-
- Turbo exhaust connection
- Flexible fitting
- Elbows
- Flanges
- Dry elbow