Product Specs
General Specifications
- Maximum Rating
- 520 BHP
- Displacement
- 760 in³
- Minimum Rating
- 385 BHP
- Governor and Protection
- Electronic (ADEM™ A3)
- RPM
- 2100 r/min
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1
- Flywheel Teeth
- 113
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 6.2 in
- Bore
- 5.1 in
Emissions
- Emissions
- EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Dimensions
- Length
- 47.3 in
- Width
- 39.9 in
- Height
- 46.7 in
- Weight
- 1976 lb
Capacity for Liquids
- Lube Oil System - Refill
- 9 gal (US)
- Cooling System
- 3.8 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
-
- Cooling System
-
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
-
- Flywheels And Flywheel Housings
-
- See Mandatory Options
-
- Fuel System
-
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
- Fuel fitting — fuel return connection: straight No. 8, 5/8-18
-
- Lube System
-
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — RH rear engine side
-
- Power Take-offs
-
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11-tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
-
- Mandatory Options
-
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
Attachments
-
- Air Compressor
-
- Air compressors
- Air chambers
- Air compressor governors
-
- Air Inlet System
-
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
-
- Belt-driven Accessories
-
- Refrigerant compressor and mounting
-
- Charging System
-
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
-
- Control System
-
- Connection
-
- Cooling System
-
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans and blower fans
- Suction fans and blower fans
- Coolant level sensor
- Aftercooler lines
-
- Exhaust System
-
- Muffler
- Flexible fitting
- Elbows, flange, pipe, clamp
- Straight exhaust adapter
-
- Fuel System
-
- Fuel lines for fuel filter
- Fuel cooler
- Fuel fitting — fuel return connection
- Flexible fuel lines
-
- Instrumentation
-
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass and remote
- Lubricating oil
- Oil filler
- Fumes disposal
-
- Mounting System
-
- Front and rear engine supports
- Structural steel base
-
- Power Take-offs
-
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front and rear
- Enclosed clutch
- Clutch support
-
- Protection System
-
- Air shutoff
- Air shutoff switch
-
- Starting System
-
- Starting System
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
-
- Transmission Arrangement
-
- Transmission cooler