Product Specs
General Specifications
- Maximum Rating
- 450 BHP
- Displacement
- 681 in³
- Minimum Rating
- 325 BHP
- Governor and Protection
- Electronic (ADEM™ A3)
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1 or SAE 2
- Flywheel Teeth
- 113 (SAE 1), 138 (SAE 2)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5.51 in
- Bore
- 5.12 in
Emissions
- Emissions
- EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA, IMO II
Dimensions
- Length
- 47.3 in
- Width
- 41.6 in
- Height
- 46.3 in
- Weight
- 1967 lb
Capacity for Liquids
- Lube Oil System - Refill
- 9 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
-
- Cooling System
-
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
-
- Flywheels And Flywheel Housings
-
- See Mandatory Options
-
- Fuel System
-
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
-
- Lube System
-
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH mid-mount
- Oil pump
- Oil valve sampling — on oil filter base
-
- Power Take-offs
-
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11 tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
-
- Mandatory Options
-
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
Attachments
-
- Air Compressor
-
- Expansion chamber
- Governors
- Fittings
-
- Air Inlet System
-
- Air cleaners
- Precleaners
- Turbo air inlet
- Air lines
-
- Belt-driven Accessories
-
- Refrigerant compressor and mounting
-
- Charging System
-
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
-
- Control System
-
- Connection
-
- Cooling System
-
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans
- Fan adapters for blower fans
- Suction fans
- Blower fans
- Coolant level sensor
- Aftercooler lines
-
- Exhaust System
-
- Muffler
- Flexible fitting
- Elbows
- Straight exhaust adapter
- Flange
- Pipe
- Rain cap
- Clamp
-
- Fuel System
-
- Fuel lines
- Fuel cooler
- Fuel fitting — fuel return and supply connections
- Flexible fuel lines
-
- Instrumentation
-
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass
- Oil filter — remote
- Lubricating oil
- Oil filler
- Fumes disposal
-
- Mounting System
-
- Front and rear engine supports
- Structural steel base
-
- Power Take-offs
-
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front
- Hydraulic pumps — rear
- Enclosed Clutch
- Clutch Support
-
- Protection System
-
- Air shutoff
- Air shutoff switch
-
- Starting System
-
- Electric starting motors — 12 Volt, 24 Volt
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
-
- Transmission Arrangement
-
- Transmission cooler